Ryeford Engineering 5 Stainless Steel Station Cleaning System with 2 Heated Ardrox 185 Initial Tank

- Stock No
- DA1416
- Manufacturer
- Ryeford Engineering
- Model
- Bunded Stainless Steel Cleaning Line.
- Year of Manufacture
- 2003
- Condition
- Seen working by RSW, Good Condition
- Work Envelope (WxDxH mm) [?]
- 675 x 630 x 590
- Process Stages
- 5 individual process stages
- Other Info
- Rear Mounted S.S. Lip Extraction
- Location
- Our Central Warehouse, Aldridge, UK
- Weight (kgs)
- 600
- External Dimensions (WxDxH mm) [?]
- 4250 x 1450 x 1000
Description
5 Station Cleaning Process System comprising 2 off Ardrox 185 Heated Initial Tanks followed by Rinse, Heated rinse and Final Submersion Tanks. Additional features include basket type operation, manual spray hose with extraction ductwork and Pre-Ardrox cleaning tank.
General description
- Total of five tanks running inline.
- Gap between tanks, keep to a minimum.
- Overall height to top of tanks 900mm
- All tanks to be the same size: Internally 700mm x 700mm opening & able to submerse a part 400mm high.
- Material: Stainless Steel.
- The submersing shelf to be able to accept a max weight of 30kg.
- Transfer parts from one tank to another with minimum effort.
- Lids / Covers for when system is not being used.
- Drain-Off system from the base of each tank.
Original Tank Line Up / Set up.
Tank 1
- Content Water Based Ardrox 185 (20%) Cleaning Solution
- Liquid Working Temp 85-95°C
- Stainless Steel Extraction Manifold Included.
Tank 2
- Content Water Based Ardrox 185 (20%) Cleaning Solution
- Liquid Working Temp - 85-95°C
- Stainless Steel Extraction Manifold Included.
Tank 3
- Content Hot & Cold Water Spray (Hand held trigger guns sufficient)
Tank 4
- Content Dewatering Oil (Gulf No-Rust 65)
- Liquid Working Temp 100°C-110°C
- Stainless Steel Extraction Manifold Included.
- Filtration / Recycling Pump System.
Tank 5
- Content Oil Dip (Evco 44AX)
- Liquid Working Temp
- Room Temp
- Filtration / Recycling Pump System
Aerospace Aftermarket Repair Station Component CleaningThis machine was originally part of an aerospace bearing remanufacturing cell that worked on the following basis. Pre-InspectionStage 1: Pre-Inspection Wash Tank and Filter to remove initial debris [DA1415 Wash Tank and Filter] Stage 1: Kerosene (Exxsol D80) Spray Wash to remove additional debris [DA1414 Vixen Tristar Conveyor Degreaser] The component is placed on the rolling table inside the spray wash; the rolling table is pushed to the far end of the spray wash through the clear plastic curtain to the rear of the clear enclosure. The nozzle of the hand held spray gun is push through the slits in the plastic curtain. The component is thoroughly sprayed until all the loose debris is removed. The rolling table is pulled back through the plastic curtain and allowed to drain for 5 minutes before inspection. InspectionComponent is inspected for wear and/or damage and categorised for repair. Machinery not applicable Clean Before RepairStage 1: Tank 1 and/or Tank 2 Ardrox 185 De-greaser [DA1416 5 Station Cleaning System] The Ardrox 185 is heated in tank 1 or tank 2 to the operating temperature of 98 to 100 degrees Centigrade before any component is placed in the tank. Once Tank 1 or 2 is at temperature the component is either placed in a basket or on its own placed into tank 1 or 2 making sure the component is fully immersed in the Ardrox 185. The component is left in tank 1 or 2 for 10 minutes. Stage 2: Tank 3 Water wash After the 10 minutes has elapsed the component is removed from tank 1 or 2 and placed in tank 3 where it is manually agitated and/or sprayed with water to remove any remnants of the Ardrox 185. Allow the component to drain sufficiently over the tank before proceeding to the next stage Stage 3: De-watering oil dip Rustilo DWX 32 After the component has been washed it is then dipped in Tank 4 containing de-watering oil this is solvent deposited rust preventative oil making sure the entire component has been immersed in the oil, after removal from tank 4 the component is placed on a trolley ready for repair. |
Additional files
Photographs taken prior refurbishment. Our refurbishment service is not available on all machines.
Machines & equipment for sale
- Surface Treatment
- Cleaning & Degreasing
- Polishing & Belt Linishing
- Mass Finishing
- Ovens & Furnaces
- Process Cooling
- Shot Blasting
- Dust & Fume Extraction
- Air Compressors
- Rectifiers & Transformers
- Miscellaneous
- Latest Stock
- Special Offers
- Direct From Site Clearances
- Auctions
- Brand New Machines
- Available Immediately
- Sell Your Machine
Machine Alert
Get the latest machines emailed directly to you as they become available to buy online sign up